When the garment factory uses the cloth inspection machine, in this process, due to its own operation errors or equipment quality doubts, equipment failures may occur. This will produce inaccurate cloth inspection, and in severe cases, it will directly fail to work, which cannot be ignored and must be dealt with in time.
The cloth inspection machine makes a lot of noise during the operation, which is probably caused by factors such as the large distance between the transmission shaft of the equipment, loose parts in a certain part, and poor lubricating oil. Just adjust and replace the parts and replace them. Unsuitable lubricating oil will do. In the cloth inspection process, the cloth is stuck in the cloth inspection process, which is probably caused by the skewed placement of the cloth. It has nothing to do with the quality of the equipment itself. The operator only needs to adjust the cloth guide roller according to the correct method. They are just parallel to each other. The brightness of the glass plate of the cloth inspection machine is low, which is mainly caused by a lot of dust and debris on the glass panel or the weakening of the brightness of the light pipe. It is only necessary to clean up the dust and debris and replace the light pipe on time.
In addition, if the cloth inspection machine does not feel smooth when guiding the cloth and rolling the cloth, such a question about the function of the cloth inspection machine is likely to be caused by a lot of dust, cloth crumbs, grease, etc. maintenance work. Insufficient illumination of the glass plate of the cloth inspection table: Insufficient illumination of the glass plate of the cloth inspection table is mainly due to the fact that the fluorescent tube and the glass plate of the cloth inspection table have dust, cloth debris, or the voltage of the lamp is unstable. This problem can be easily solved by frequently removing the dust and cloth crumbs on the fluorescent tube and the glass plate of the cloth inspection table, and stabilizing the lighting voltage. Inaccurate length measurement of the duplicating device: During the conveying process of the fabric, the friction force is not enough, the length-measuring wheel is worn for a long time, or the work is blocked, etc., which may cause the inaccurate length measurement of the duplicating device of the cloth inspection machine. Such as increasing the relative temperature of the cloth to increase the friction of the conveying movement of the cloth, replacing the length gauge wheel, and often cleaning the dust and oil on the gauge wheel to deal with it. Other working faults: If the equipment is not filled with lubricating oil for a long time, the equipment will show other working faults during the working process.
The cloth inspection machine makes a lot of noise during the operation, which is probably caused by factors such as the large distance between the transmission shaft of the equipment, loose parts in a certain part, and poor lubricating oil. Just adjust and replace the parts and replace them. Unsuitable lubricating oil will do. In the cloth inspection process, the cloth is stuck in the cloth inspection process, which is probably caused by the skewed placement of the cloth. It has nothing to do with the quality of the equipment itself. The operator only needs to adjust the cloth guide roller according to the correct method. They are just parallel to each other. The brightness of the glass plate of the cloth inspection machine is low, which is mainly caused by a lot of dust and debris on the glass panel or the weakening of the brightness of the light pipe. It is only necessary to clean up the dust and debris and replace the light pipe on time.
In addition, if the cloth inspection machine does not feel smooth when guiding the cloth and rolling the cloth, such a question about the function of the cloth inspection machine is likely to be caused by a lot of dust, cloth crumbs, grease, etc. maintenance work. Insufficient illumination of the glass plate of the cloth inspection table: Insufficient illumination of the glass plate of the cloth inspection table is mainly due to the fact that the fluorescent tube and the glass plate of the cloth inspection table have dust, cloth debris, or the voltage of the lamp is unstable. This problem can be easily solved by frequently removing the dust and cloth crumbs on the fluorescent tube and the glass plate of the cloth inspection table, and stabilizing the lighting voltage. Inaccurate length measurement of the duplicating device: During the conveying process of the fabric, the friction force is not enough, the length-measuring wheel is worn for a long time, or the work is blocked, etc., which may cause the inaccurate length measurement of the duplicating device of the cloth inspection machine. Such as increasing the relative temperature of the cloth to increase the friction of the conveying movement of the cloth, replacing the length gauge wheel, and often cleaning the dust and oil on the gauge wheel to deal with it. Other working faults: If the equipment is not filled with lubricating oil for a long time, the equipment will show other working faults during the working process.
